Cisco Simulator

Routing: [Gen][CCNA][CCNP Route][CCNP Remote][CCDA][MPLS][EEM][Add][Juniper][ACL][Host]
Switching: [CCNP Switch] [Switch Add] [Intro] [VLANs] [MLS] [STP] [QoS] [Availability]
Security: [CCNP Security] [CCNA Security] [CCNP ISCW][PIX] [Adv PIX/ASA] [Net Sec1] [Net Sec2]
Wireless: [Wireless] [Wireless Chall] [CCNA Wireless] [Wireless Theory]
Voice: [Voice/QoS] [CCNA Voice] [CCVP Gateway] [CCVP Voice]
Topics: [Dot1q][Dot1x][BGP][BRI][DHCP][IGRP][IGMP][OSPF][PPP][QoS][RADIUS][RIP][Subnet][SNMP][VLAN]

Our router and switch simulators are now available for demonstration in a number of areas:

Routing

• [General examples]
• [CCNA][CCNA (Cisco Academy)]
• [Routing][Remote Access]
• [CCDA][MPLS]
• [EEM][Router (Additional)]
• [Juniper]

Switching

• [CCNP Switch][Switch (Additional)]
• Switching: Introduction. Go.
• Switching: VLANs. Go.
• Switching: MLS. Go.
• Switching: STP. Go.
• Switching: QoS. Go.
• Switching: Availability. Go.

Security

• [CCNA Security][CCNP Security]
• [CCNP ISCW][PIX/ASA]
• [Advanced PIX/ASA][Cisco Network Security 1]
• [Cisco Network Security 2]

Wireless

• Wireless [link].
• [Wireless][CCNA Wireless]
• [Wireless Theory]

Voice/QoS

• [Voice/QoS][CCNA Voice]
• [CCVP Gateway][CCVP Voice]

Router Simulator

Cisco Router. Some samples are:

• [Challenge 1]. This challenge involves the configuration of the E0 port on a router.
• [Challenge 2]. This challenge involves the setting up the serial port parameters.
• [Challenge 3]. This challenge involves the configuration of the name server, user names and passwords.
• [Challenge 4]. This challenge involves the configuration of the interface ports.

Switch Simulator

Cisco Switch. Some samples are:

• [Challenge 1]. This challenge involves the configuration of ethernet port settings and CDP.
• [Challenge 2]. This challenge involves the configuration of the Ethernet ports.
• [Challenge 3]. This challenge involves the configuration of passwords, and usernames
• [Challenge 4]. This challenge involves the configuration the host table, hostname and default gateway.

Cisco Aironet 1200 Simulator

Cisco Aironet . Some samples are:

• [Challenge 1]. BVI_parameters. This challenge involves the configuration of the BVI interface.
• [Challenge 2]. E0_parameters. This challenge involves the configuration of the E0 interface
• [Challenge 3]. Host_name_and_Default.
• [Challenge 4]. SSID_Hostname_Domain_Name
• [Challenge 5]. Passwords_Usernames_and_HTTP

Cisco PIX/ASA

Cisco PIX/ASA. Some samples are:

• [Challenge 1]. This challenge involves the configuration of basic PIX details for E0.
• [Challenge 2]. E1_and_E2_details
• [Challenge 3]. Port_Names_and_Username
• [Challenge 4]. Passwords_and_Banners
• [Challenge 5]. This challenge involves the configuration of a static route, and some banners.

Juniper

Juniper. Some samples are:

• [Challenge 1]. The configure command within operation is used, the system is in candidate config, which must then be committed before it is used in a running configuration. This challenge provides an introduction to JunOS commands.
• [Challenge 2]. This challenge adds additional services for the Juniper device, such as enabling SSH, a time-zone and a new user.
• [Challenge 3]. This challenge adds additional services for the Juniper device, such as defining the loopback (lo0) address, defining an Ethernet IP address, and adding a new user.
• [Challenge 4]. This challenge adds additional services for the Juniper device, such as enabling SSH, TELNET, finger, FTP and Netconfig. It also involves setting the baud rate for the serial console port.
• [Challenge 5]. This challenge shows some basic system information, such as the JUNOS version, the interface details and users.

Host

We are currently working on this. Some samples are:

• [Host]

Themes

Some samples are:

• [ACLs]. This has some ACL challenges.

Commands

• [Cisco commands]
• [Juniper commands]

Demos